精品偷拍一区二区三区在线看_97se狠狠狠狠狼鲁亚洲综合色_欧美成人一区二免费视频软件_99久久精品费精品国产一区二区_97超级碰碰人妻中文字幕

粘度計|旋轉粘度計廠家|運動粘度計|烏氏粘度計廠家_上海標卓

主頁 > 使用方法 >

粘度計英文使用說明書

 

This instrument is widely supplied in measuring axunge paint plastic, food, medication, adhesive, cosmetic and so on like fluidic sticky resistance and liquid absolute viscosity.fix and measuring must be done according requirement from instruction book。
 
Main technic spec
 
·Range of measure:10~105mpa.s
·Rotate speed: 6,12,30,60turn/minute
·Error of measure:±5%(Newton liquid)
·Power:220V±10%
         50Hz
 
Fix

1.     take out chassis base
andsupport from packing
boxcircumrotate three
level 。
2.adjust foot into tapping
hole in chassis base(chart 1)
3.main machine fix:
a. take out main machine by unscrewing the screws in chassis
b. unscrew the handle root screw . inset the power line into handle slot(chart2)
c. penetrate the handle into hole under slot(chart2)
d. screw the handle fix knob to screw the handle and keep the main machine level mostly (chart3)
 
 
8.measure the temperature of measured liquid directly , do not use the temperature value of constant temperature bath
9. it is normal when the viscosity changes because of change of speed and length of measure time during measuring. That is not the instrument hitch.
10.operate seriously according the operation manual
 
 

The whole set

1.main machine————————1
2.(1,2,3,4)rotors———— 1
3.protective support—————— 1
4.support——————————  1
5.lever adjustment screw———— 3
6.manual——————————  1
7.certificate ————————— 1
 
Quotiety table
 
     Run/minute
rotor
60 30 12 6
1 1 2 5 10
2 5 10 25 50
3 20 40 100 200
4 100 200 500 1000
 

 

Notice

1.this instrument should be used in 10—30
2.protective support must be fixed when measuring, or the viscosity value will change as the change of diameter of container
3.the rotor connective screw staff should be raised when fix or remove rotor, or the head of shaft will be damaged. Keep the bleb from rotor when rotor is immerged into liquid
4.the instrument should not be placed in oblique or inverse direction. Especially the rotor is fixed.
5.after fixing the rotor, do not turn on machine to turn the rotor without immerging the rotor into liquid
6.remove rotor carefully after finishing work every time.  Clear it extremely, dry is with blower, and put it back on the rotor support in vertically
7.pointer lock staff should be packaged by yellow package cover and rubber hand when carrying the instrument.
 


 
e. remove the rubber hand from pointer lock staff and yellow package cover from main machine inferior part.
alarm: do not turn on machine before removing the above two objects or it will damage the machine
power on, adjust the level adjustment foot(chart4). Make the bleb in the middle of level set(chart5).
 
Operation
 
1.first rightly rotate the protective support into the instrument inferior part.
2.prepare the liquid for measuring, select the column container having diameter not less than 70 mm
3.control the temperature in liquid for measuring correctly according the precision required by measuring
4. select the right rotor number by estimating the approximate range of viscosity of liquid or measuring, and rotate left the rotor into the connective screw staff(chart4),then rotate the up and down knob(chart5),make the instrument down slowly, immerging into measured liquid gradually, until the rotor liquid level balances the liquid level(chart4).put down the pointer lock staff, power on, relax.

the pointer lock staff,
to make the rotor
circumrotate in the
liquid. The speed is
20-30 run, until the
pointer stay at one
position . put down
the pointer lock staff to
make the reading unchangeable,
then turn off the motor to
make the pointer stay
in the range of reading
window,then get the
reading directly. If the
pointer do not stay in
the frame after turning
off motor, go on to put
down the pointer lock
staff. Repeat the action 
of turning on and off to
make the pointer in the
frame of window. If
selecting 6 and 12 turn /minute,
get the reading directly
without locking the pointer.5.the best is that the read pointer stay 30—90 division range, or change the rotor number or run speed to get the requirement 6.when you can not predict the viscosity value of liquid for measuring , the rotor and turn speed knob should be selected by turning from little value to big value, and from slow to fast, to measure the viscosity value.
 
 
Quotiety  and error correcting
1.the absolute viscosity value of liquid measured can be get by multiplying the reading pointed on dial when measuring and quotiety in quotiety table
that is:
η(mpa.s=k×α
k= quotiety
α=pointer reading
η=viscosity value
2.frequency error correcting
                                     normal frequency
actual viscosity value= indicated value ×—————————
                              actual frequency
 
 

 

Range stable and quotiety table

range stable
rotor Turn/minute
60 30 12 6
1 100 200 500 1000
2 500 1000 2500 5000
3 2000 4000 10000 20000
4 10000 20000 50000 100000
 
 
 

 


[上一篇:烏氏粘度計原理及其應用 ]    [下一篇:美國 BROOKFIELD博勒飛粘度計使用說明書 ]

使用方法

常見問題

瀏覽更多同類產品

STM-IVB斯托默粘度計
STM-IVB斯托默粘度計
 NDJ-1E 旋轉粘度計
NDJ-1E 旋轉粘度計
NDJ-1D 布氏旋轉粘度計
NDJ-1D 布氏旋轉粘度計
烏氏粘度計
烏氏粘度計
主站蜘蛛池模板: 午夜福利理论片在线观看播放| 久久久国产乱子伦精品| 国产精品久久久久久久妇| 色综合久久久久综合体桃花网| 乱人伦精品视频在线观看 | 亚洲精品乱码久久久久久蜜桃| 中国少妇内射xxxx狠干| 18禁男女爽爽爽午夜网站免费| 狠狠热精品免费视频| 国产精品美女久久久久av超清| 色五月激情五月| 国产亚洲av综合人人澡精品| 无线日本视频精品| 成人久久久久久久久久久| 麻豆一区二区在我观看| 狠狠色噜噜狠狠狠8888米奇| 亚洲国产中文在线二区三区免| 欧美无人区码suv| а中文在线天堂| 激烈的性高湖波多野结衣| 丰满人妻被黑人猛烈进入| 精品国产乱码久久久久乱码| 亚洲 自拍 另类 欧美 综合| 无码人妻丰满熟妇啪啪7774| 精品久久久bbbb人妻| 少妇被爽到高潮动态图| 熟女性饥渴一区二区三区| 2019最新国产不卡a| 日本少妇被黑人xxxxx| 国产免费无遮挡吸乳视频| 亚洲aⅴ男人的天堂在线观看| 全球av集中精品导航福利| 午夜伦情电午夜伦情电影| 最近中文av字幕在线中文| 无码人妻丰满熟妇啪啪网站| 国产乱码一区二区三区爽爽爽| 骚片av蜜桃精品一区| 亚洲熟妇久久国产精品| 亚洲av无码国产在丝袜线观看| 粗大的内捧猛烈进出视频| av一本久道久久综合久久鬼色 |